Wood play kitchen furniture can be so expensive. Yet these minature cuties are so easy and fun to construct. We have a whole collection of plans offered online for play cooking areas. This one was constructed by The Crafting Chicks. To see Grace's initial Playhouse Kitchen sink, scroll down.
20" high x 16" wide x 12" deep
Preparation
GOING SHOPPING LIST
1 - 1x12 @ 8'
1 - 1x2 @ 8' (browse for a scrap piece, or conserve the leftovers for the range and refrigerator).
1 - 1x4 @ 8' (again, you just need a bit, so conserve the leftovers for the stove and fridge).
1-- scrap piece of plywood (I utilize beadboard) 12x20. If needed, you might omit this.
Metal pan or dish to utilize as the sink (I utilized a sink from a plastic kitchen handed down from my niece.
COMMON MATERIALS.
Elmer's Wood Glue.
Elmer's Wood Filler.
120 grit sandpaper.
guide.
paint.
paint brush.
CUT LIST.
( 2) 1x12 @ 20" Sides.
( 1) 1x2 @ 14 1/2" Toekick.
( 2) 1x12 @ 14 1/2" Shelves.
( 1) 1x12 @ 16 1/2" Countertop.
( 1) 1x4 @ 16 1/2" Backsplash.
( 1) 1x4 @ 14 1/2" Front of Sink.
( 1) 16x20 piece of plywood for the back.
CUTTING INSTRUCTIONS.
You will require to use a jigsaw to cut out the sink hole.
TOOLS.
Measuring tape.
Speed Square.
Safety Glasses.
Hearing Protection.
Drill.
Jigsaw.
Brad Nailer.
Power Sander.
BASIC INSTRUCTIONS.
In addition to basic safety and structure directions, please note, you can construct with either screws or glue on this one.
Directions.
ACTION 1.
1. Start Building package. Begin by attatching A to C as shown. The bottom of C will rest 1 1/2" from the bottom of C, leaving the precise quantity of area for B, the toekick.
STEP 2.
2. Finish the box. Finish attatching the boards as revealed, leaving 1/4 inch overhand on the sides of the counter top.
STEP 3.
3. Counter-Top. I suggest connecting the backslash to the counter-top very first, then connecting the whole counter-top/backslash unit to the sink base as one. This will leave a 3/4 inch overhand on the front.
ACTION 4.
Here are some extra views. Note the front of sink is put in.
STEP 5.
ACTION 6.
Sink. Choose what you will be using for a sink. Then cut the hole to fit the sink. I utilized a sink I took off a junk hand-me-down kitchen from my niece. You might likewise utilize a metal pan or even a plastic tupperware. Just make certain there is a lip to keep the sink in location. You could even just include a third shelf to box in the sink.
ACTION 7.
Ending up Instructions.
Preparation Instructions.
Fill any exposed holes with wood filler and let dry. Use a second coat if required. Sand with medium grit sandpaper. Tidy task and work surface area. Prime and paint as preferred.
Complete Used.
Ending up. Fill any nail holes with wood filler and sand, paint, and enjoy! Oh, do not forget to put your sink in (glue not recommended, Grace's is glued in, and it would be nice to be able to take the sink out and clean it).
20" high x 16" wide x 12" deep
Preparation
GOING SHOPPING LIST
1 - 1x12 @ 8'
1 - 1x2 @ 8' (browse for a scrap piece, or conserve the leftovers for the range and refrigerator).
1 - 1x4 @ 8' (again, you just need a bit, so conserve the leftovers for the stove and fridge).
1-- scrap piece of plywood (I utilize beadboard) 12x20. If needed, you might omit this.
Metal pan or dish to utilize as the sink (I utilized a sink from a plastic kitchen handed down from my niece.
COMMON MATERIALS.
Elmer's Wood Glue.
Elmer's Wood Filler.
120 grit sandpaper.
guide.
paint.
paint brush.
CUT LIST.
( 2) 1x12 @ 20" Sides.
( 1) 1x2 @ 14 1/2" Toekick.
( 2) 1x12 @ 14 1/2" Shelves.
( 1) 1x12 @ 16 1/2" Countertop.
( 1) 1x4 @ 16 1/2" Backsplash.
( 1) 1x4 @ 14 1/2" Front of Sink.
( 1) 16x20 piece of plywood for the back.
CUTTING INSTRUCTIONS.
You will require to use a jigsaw to cut out the sink hole.
TOOLS.
Measuring tape.
Speed Square.
Safety Glasses.
Hearing Protection.
Drill.
Jigsaw.
Brad Nailer.
Power Sander.
BASIC INSTRUCTIONS.
In addition to basic safety and structure directions, please note, you can construct with either screws or glue on this one.
Directions.
ACTION 1.
1. Start Building package. Begin by attatching A to C as shown. The bottom of C will rest 1 1/2" from the bottom of C, leaving the precise quantity of area for B, the toekick.
STEP 2.
2. Finish the box. Finish attatching the boards as revealed, leaving 1/4 inch overhand on the sides of the counter top.
STEP 3.
3. Counter-Top. I suggest connecting the backslash to the counter-top very first, then connecting the whole counter-top/backslash unit to the sink base as one. This will leave a 3/4 inch overhand on the front.
ACTION 4.
Here are some extra views. Note the front of sink is put in.
STEP 5.
ACTION 6.
Sink. Choose what you will be using for a sink. Then cut the hole to fit the sink. I utilized a sink I took off a junk hand-me-down kitchen from my niece. You might likewise utilize a metal pan or even a plastic tupperware. Just make certain there is a lip to keep the sink in location. You could even just include a third shelf to box in the sink.
ACTION 7.
Ending up Instructions.
Preparation Instructions.
Fill any exposed holes with wood filler and let dry. Use a second coat if required. Sand with medium grit sandpaper. Tidy task and work surface area. Prime and paint as preferred.
Complete Used.
Ending up. Fill any nail holes with wood filler and sand, paint, and enjoy! Oh, do not forget to put your sink in (glue not recommended, Grace's is glued in, and it would be nice to be able to take the sink out and clean it).
Tidak ada komentar:
Posting Komentar